|
Wired / Wireless IR IP Camera
ICA-108 / ICA-108W
Quick Installation Guide
Chapter 1. Introduction
Thank you for purchasing the ICA-108/ICA-108W. It is versatile and high image
solution of surveillance application for day and night. The ICA-108/ICA-108W is
also a stand-alone camera system with a built-in processor and web server that
provides highest quality video and system performance.
1.1 Before Installation
Before installation, please be sure to read this quick installation guide and user’s
manual (CD) carefully to complete machine installation.
1.2 System Requirements
Network Interface
Monitoring System
10/100MBase-TX Ethernet, IEEE802.11b/g (ICA-108W only)
Recommended for Internet Explorer 6.0 or later
• CPU: Pentium 4, 1.5GHz or above
• Memory Size : 512 MB (512 MB or above
Recommended)
• VGA card resolution : 1024 x 768 or above
• Network bandwidth: In VGA resolution mode,
minimum upload bandwidth is 1Mbps.
System Hardware
1.3 Package Content
ICA-108/ICA-108W x 1
Power Adapter x 1
Wall Mount Accessories x 1
External Antenna x 1 (ICA-108W only)
CD Disk x 1
Quick Installation Guide x 1
ꢀ
Chapter 2. Physical Installation
1.Connect an Ethernet cable
Connect the LAN cable on the ICA-108/ICA-108W to the network device (hub or
switch).
2.Attach the antenna (ICA-108W only)
Finds antenna in accessory and attaches the antenna to the ICA-108W SMA
connector.
3.Check the LED (Front Panel)
The LED is defined to identify LAN/WLAN connection type. When LAN port is
connected, the LED will be green. For WLAN model, if LAN ported is connected,
the LED will be green; if LAN cable is removed; the ICA-108W will change to
WLAN connection and LED change to orange color.
4. Place the ICA-108/ICA-108W on the table or fix it onto ceiling or wall
Use screws to fix the ICA-108/ICA-108W onto the ceiling or wall. You could also
put the ICA-108/ICA-108W in the table directly.
5.Attach the power supply
Plug in power adapter and connect to power source. After power on, ICA-108/
ICA-108W will start to operate.
Only use the power adapter supplied with ICA-108/ICA-108W.
Otherwise, the product may be damaged
Note
ꢁ
Chapter 3. IP Wizard
This chapter shows how to quick set up your ICA-108/ICA-108W. The ICA-108/ICA-
108W is with the default settings. However to help you find the networked camera
quickly the windows utility-IP Wizard can search the cameras in the network
that shall help you to configure some basic setting before you started advanced
management and monitoring.
3.1 Installation
In the installation steps below, this guide use ICA-108 as the
example. However, the steps for ICA-108W are similar.
Note
1. Insert the bundled CD into the CD-ROM drive to launch the autorun program.
Once completed, a welcome menu screen will appear.
2. Click the “IP Wizard” hyperlink; you will see the InstallShield Wizard dialog box
as below.
If the welcome screen does not appear, click “Start” at the taskbar.
Then, select “Run” and type “D:\Utility\setup.exe”, assume D is
your CD-ROM drive.
Note
3. The “Welcome to the InstallShield Wizard for IP Wizard” will display on the
screen and click “Next” to continue.
ꢂ
4. Please click “Next” to install with original settings, or you may click “Change…”
button to modify the install folder then press “Next” to continue.
5. Please click “Install” to start the installation.
ꢃ
6. Please click “Finish” to complete the installation
7. Please double-click the utility icon
ICA-108 utility.
on the desktop then you will see the
8. Press “Search” button. IP Wizard will list all IP Cameras in your LAN environ-
ment:
ꢄ
3.2 Wizard function
Please select your ICA-108 and press “Wizard”. The utility featured
of “Wizard” function to help user to initial ICA-108. User can setup
IP address, username and password step by step.
Note
Please enter User Name and Password. Default Username is: admin, leave
password blank. Then click “Submit”.
ꢅ
3.3 Username and Password
You may change the ID and assign a new password to your ICA-108 or keep the
original and press “Next” to continue.
As below, you can select “Static IP” and enter the IP settings. Or select “DHCP ON”
when there is a DHCP server in your network.
If no IP address is assigned after 30 seconds, ICA-108/ICA-108W
will use its default address 192.168.0.20.
Note
User may open the web browser, and key in the IP address (for example:
http://192.168.0.20, the default IP address) in the address field to login web
configuration page and refer to the User’s manual in the bundled CD disk for more
configuration.
ꢆ
Chapter 4. Cam Viewer Installation
This chapter will guide you to install the central management software. The ICA-
108/ICA-108W can be managed through its web interface. However, to central
control, manage or record the cameras installed in the network Cam Viewer, the
windows-based central management software are required.
The Cam Viewer Pro 30 days trial version installation steps are
similar. Below is the installation of Cam Viewer Lite.
Note
1. Insert the bundled CD disk into the CD-ROM drive to launch the autorun
program. Once completed, a welcome page will appear in IE. Click the “Cam
Viewer Lite” hyperlink, the below InstallShield Wizard dialog box will appear.
If the welcome screen does not appear, click “Start” at the taskbar.
Then, select “Run” and type “D:\Cam Viewer Lite\setup.exe”,
Note
assume “D” is your CD-ROM drive.
2. Selects the language which you want, Cam Viewer is current including fifteen
languages. Please select one of the languages and click ”Next” to continue.
10
3. The welcome screen will display on the screen, please click “Next”.
4. Please read the license agreement and then check “I accept the terms of the
license agreement” if you are agreed and click “Next” to continue the installation
11
5. Please key in user name and company name for which you want and click “Next”
to continue installation.
6. Check the option “Complete” – all program features will be installed (Requires
the most disk space) and click “Next” to continue installation.
12
7. “Ready to Install the Program” will appear to prompt you to start the installation.
Please click “Install” to start.
8. Please click “No” to finish the Cam Viewer Lite installation.
In above step, when Cam Viewer works with MBM5 (Motherboard
Monitor 5), Cam Viewer will display CPU temperature and fan
speed. Please click “Yes” if you need this function and refer to the
Note
manual of Cam Viewer CD disk for complete installation.
Now, you can central manage all the ICA-108/ICA-108W installed in your network.
Please refer to the Cam Viewer guide in the CD-ROM for more.
1ꢀ
Appendix A: Feature Listing for Cam Viewer
Cam Viewer Lite
Cam Viewer Pro
Software Version
(Free Bundle version)
(30-day Trial version)*
IP Camera Input
Dual Monitor
Smart Guard
I/O Device
32
-
16 / 32 / 64
V
V
V
V
V
-
V
-
Hotline
Address Book
-
Unusual event
System log
Counting application
Unusual event
System log
Log Viewer
Counting Application
Remote Playback Server
Concurrent Playback
Counting Function
-
2 way counting
Unlimited
16 Channels
V
-
1 Channel
-
General Motion
Missing Object
Foreign Object
Lose Focus
Smart Search
General Motion
Camera Occlusion
Remote Live Viewer
1 Channel
16 Channel
*Remark: Refer to Appendix B for more
1ꢁ
Appendix B: Suggest Hardware / System Requirement
Total FPS
~600
600~480 480~240 240~120
120~
Intel Core
2 Duo
QX6800
Intel Core
2 Duo
E6600
Intel
Pentium D
930
Intel P4
3.0 GHz
Intel P4
2.8 GHz
CPU
RAM
4 GB
2 GB
2 GB
1 GB
1 GB
Chipset of
Motherboard
Intel 946 or 965 chip, Intel Chipset recommended
ATI Radeon 9200, nVIDIA GeForce FX-5200,
Intel 945/965 or above
VGA Card
Ethernet
Hard Disk
O.S.
100 Base-TX or Above, Gigabit LAN recommended
160 GB or above
Windows 2000 / XP / 2003
Total FPS: Means all the cameras will spend how many frames when this software
works. Suppose there are 10 cameras, each one will work with 30fps;
the total fps should be 300fps.
Ordering Information for Cam Viewer Pro
Model
CVP-4
Description
4-Channel Cam Viewer Professional
8-Channel Cam Viewer Professional
16-Channel Cam Viewer Professional
32-Channel Cam Viewer Professional
64-Channel Cam Viewer Professional
CVP-8
CVP-16
CVP-32
CVP-64
Further Configuration
If you want to configure more detail settings of ICA-108/ICA-108W, please refer to
the user manual in the CD disk.
1ꢂ
This page is intentionally left blank
|