Porter Cable Sander 352VS User Manual

ESPAÑOL: PÁGINA 15  
FRANÇAISE : PAGE 31  
Instruction  
manual  
BELT SANDER  
MODEL352VS  
IMPORTANT  
Please make certain that the person who is  
to use this equipment carefully reads and  
understands these instructions before  
starting operations.  
To learn more about Porter-Cable  
visit our website at:  
The Model and Serial No. plate is located on the main  
housing of the tool. Record these numbers in the  
spaces below and retain for future reference.  
Model No. ______________________________________  
Type ___________________________________________  
Serial No._______________________________________  
Copyright © 2003 Porter-Cable Corporation  
Part No. 899748 - 04-21-03  
 
2. Avoid body contact with grounded surfaces such as pipes,  
radiators, ranges and refrigerators. There is an increased risk of electric  
shock if your body is grounded.  
3. Don’t expose power tools to rain or wet conditions. Water entering a  
power tool will increase the risk of electric shock.  
4. Do not abuse the cord. Never use the cord to carry the tools or pull  
the plug from an outlet. Keep cord away from heat, oil, sharp edges or  
moving parts. Replace damaged cords immediately. Damaged cords  
increase the risk of electric shock.  
5. When operating a power tool outside, use an outdoor extension  
cord marked “W-A” or “W”. These cords are rated for outdoor use and  
reduce the risk of electric shock.  
PERSONAL SAFETY  
1. Stay alert, watch what you are doing, and use common sense when  
operating a power tool. Do not use tool while tired or under the  
influence of drugs, alcohol, or medication. A moment of inattention while  
operating power tools may result in serious personal injury.  
2. Dress properly. Do not wear loose clothing or jewelry. Contain long  
hair. Keep your hair, clothing, and gloves away from moving parts.  
Loose clothes, jewelry, or long hair can be caught in moving parts.  
3. Avoid accidental starting. Be sure switch is OFF before plugging in.  
Carrying tools with your finger on the switch or plugging in tools that have  
the switch ON invites accidents.  
4. Remove adjusting keys or wrenches before turning the tool ON. A  
wrench or a key that is left attached to a rotating part of the tool may result  
in personal injury.  
5. Do not overreach. Keep proper footing and balance at all times.  
Proper footing and balance enable better control of the tool in unexpected  
situations.  
6. Use safety equipment. Always wear eye protection. Dust mask, non-  
skid safety shoes, hard hat, or hearing protection must be used for  
appropriate conditions.  
7. Use certified safety equipment. Eye protection equipment should  
comply with ANSI Z87.1 standards, hearing equipment should comply with  
ANSI S3.19 standards, and dust mask protection should comply with  
MSHA/NIOSH certified respirator standards.  
TOOLS USE AND CARE  
1. Use clamps or other practical way to secure and support the  
workpiece to a stable platform. Holding the work by hand or against your  
body is unstable and may lead to loss of control.  
2. Do not force tool. Use the correct tool for your application. The  
correct tool will do the job better and safer at the rate for which it is  
designed.  
3. Do not use tool if switch does not turn it ON or OFF. A tool that  
cannot be controlled with the switch is dangerous and must be repaired.  
4. Disconnect the plug from the power source before making any  
adjustments, changing accessories, or storing the tool. Such preventive  
safety measures reduce the risk of starting the tool accidentally.  
3
2
 
5. Store idle tools out of reach of children and other untrained  
persons. Tools are dangerous in the hands of untrained users.  
6. Maintain tools with care. Keep cutting tools sharp and clean.  
Properly maintained tools, with sharp cutting edges are less likely to bind  
and are easier to control.  
7. Check for misalignment or binding of moving parts, breakage of  
parts, and any other condition that may affect the tool’s operation. If  
damaged, have the tool serviced before using. Many accidents are  
caused by poorly maintained tools.  
8. Use only accessories that are recommended by the manufacturer  
for your model. Accessories that may be suitable for one tool may become  
hazardous when used on another tool.  
SERVICE  
1. Tool service must be performed only by qualified repair personnel.  
Service or maintenance performed by unqualified personnel may result in a  
risk of injury.  
2. When servicing a tool, use only identical replacement parts. Follow  
instructions in the Maintenance Section of this manual. Use of  
unauthorized parts or failure to follow Maintenance Instructions may create a  
risk of electric shock or injury.  
SPECIFIC SAFETY RULES AND SYMBOLS  
1. Hold the tool by the insulated gripping surfaces when performing an  
operation where the cutting tool may contact hidden wiring or its own  
cord. Contact with a “live” wire will make exposed metal parts of the tool  
“live” and will shock the operator.  
2. Use proper safety equipment. Wear safety goggles for eye protection,  
wear hearing protection, and wear a protective mask to minimize breathing in  
the fine dust created while sanding.  
3. Sanding of lead-based paint is not recommended. Lead-based paint  
should only be removed by a professional.  
4. Always maintain a firm grip on the belt sander handles with both hands  
to prevent loss of control.  
5. Do not operate belt sander without all guards and covers securely in  
place.  
6. Some wood contains preservatives which can be toxic. Take extra  
care to prevent inhalation and skin contact when working with these  
materials. Request and follow any safety information available from your  
material supplier.  
This tool was designed for certain applications. DO NOT  
modify and/or use it for any application other than for which  
it was designed. If you have any questions relative to its application, DO NOT  
use the tool until you have written Porter-Cable and we have advised you.  
Technical Service Manager  
Porter-Cable Corporation  
4825 Highway 45 North  
Jackson, TN 38305  
4
 
SYMBOL  
DEFINITION  
........................ volts  
V
A
........................ amperes  
........................ hertz  
........................ watts  
........................ kilowatts  
........................ microfarads  
........................ liters  
Hz  
W
kW  
µF  
l
kg  
........................ kilograms  
N/cm2 ........................ newtons per square centimeter  
Pa  
h
min  
s
........................ pascals  
........................ hours  
........................ minutes  
........................ seconds  
........................ alternating current  
3
........................ three-phase alternating current  
3N  
........................ three-phase alternating current with neutral  
........................ direct current  
........................ no load  
n0  
........................ alternating or direct current  
........................ Class II Construction  
........................ splash-proof construction  
........................ watertight construction  
…/min ........................ revolutions or reciprocation per minute  
ADDITIONAL SAFETY RULES FOR PAINT REMOVAL  
Extreme care should be taken when removing paint. The  
peelings, residue, and vapors of paint may contain lead,  
which is poisonous. Exposure to even low levels of lead can  
cause irreversible brain and nervous system damage. Young  
and unborn children are particularly vulnerable.  
Before beginning any paint removal process you should determine whether  
the paint you are removing contains lead. This can be done by your local  
health department or by a professional who uses a paint analyzer to check for  
lead.  
LEAD-BASED PAINT SHOULD ONLY BE REMOVED BY A PROFESSIONAL.  
Persons removing paint should follow these guidelines:  
1. KEEP THE WORK AREA WELL VENTILATED. Open the windows and  
put an exhaust fan in one of them. Be sure the fan is moving air from inside  
to outside.  
2. REMOVE OR COVER any carpets, rugs, furniture, clothing, cooking  
utensils, and air ducts.  
3. PLACE DROP CLOTHS in the work area to catch any paint chips or  
peelings. Wear protective clothing such as extra work shirts, overalls and hats.  
5
 
4. WORK IN ONE ROOM AT A TIME. Furnishings should be removed or  
placed in the center of the room and covered. Work areas should be sealed  
off from the rest of the dwelling by sealing doorways with drop cloths.  
5. CHILDREN, PREGNANT, OR POTENTIALLY PREGNANT women and  
nursing mothers should not be present in the work area until the work is  
done and all cleanup is complete.  
6. WEAR A DUST RESPIRATOR or a dual filter (dust and fume) respirator  
mask which has been approved by the Occupational Safety and Health  
Administration (OSHA), the National Institute of Safety and Health (NIOSH),  
or the United States Bureau of Mines. These masks and replaceable filters  
are readily available at major hardware stores. Be sure the mask fits. Beards  
and facial hair may keep the masks from sealing properly. Change filters  
often. DISPOSABLE PAPER MASKS ARE NOT ADEQUATE.  
7. KEEP FOOD AND DRINK out of the work area. Wash hands, arms, and  
face and rinse mouth before eating or drinking. Do not smoke or chew gum  
or tobacco in the work area.  
8. CLEAN UP ALL REMOVED PAINT and dust by wet mopping the floors.  
Use a wet cloth to clean all walls, sills and any other surfaces where paint or  
dust is clinging. DO NOT SWEEP, DRY DUST OR VACUUM. Use a high  
phosphate detergent or trisodium (TSP) to wash and mop areas.  
9. AT THE END OF EACH WORK SESSION, put the paint chips and debris  
in a double plastic bag, close it with tape or twist ties and dispose properly.  
10. REMOVE PROTECTIVE CLOTHING and work shoes in the work area to  
avoid carrying dust into the rest of the dwelling. Wash work clothes  
separately. Wipe shoes off with a wet rag, then wash that rag with the work  
clothes. Wash hair and body thoroughly with soap and water.  
REPLACEMENT PARTS  
When servicing, use only identical replacement parts.  
MOTOR  
Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60  
cycle A.C. current and voltage within plus or minus 5 percent of that shown  
on the specification plate on the tool. Several models, however, are designed  
for A.C. current only. Refer to the specification plate on your tool for proper  
voltage and current rating.  
Do not operate your tool on a current on which the voltage is  
not within correct limits. Do not operate tools rated A.C. only  
on D.C. current. To do so may seriously damage the tool.  
EXTENSION CORD SELECTION  
If an extension cord is used, make sure the conductor size is large enough to  
prevent excessive voltage drop which will cause loss of power and possible  
motor damage. A table of recommended extension cord sizes will be found  
in this section. This table is based on limiting line voltage drop to 5 volts (10  
volts for 230 volts) at 150% of rated amperes.  
5
6
 
If an extension cord is to be used outdoors it must be marked with the suffix  
W-A or W following the cord type designation. For example – SJTW-A to  
indicate it is acceptable for outdoor use.  
RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS  
Length of Cord in Feet  
115V  
230V  
25 Ft.  
50 Ft.  
50 Ft.  
100 Ft. 150 Ft. 200 Ft.  
250 Ft. 300 Ft.  
500 Ft. 600 Ft.  
400 Ft. 500 Ft.  
800 Ft. 1000 Ft.  
100 Ft. 200 Ft. 300 Ft. 400 Ft.  
0-2  
2-3  
18  
18  
18  
18  
18  
18  
18  
16  
16  
16  
14  
14  
18  
18  
18  
18  
16  
16  
14  
14  
12  
12  
12  
12  
18  
16  
16  
14  
14  
12  
12  
10  
10  
10  
8
16  
14  
14  
12  
12  
10  
10  
8
16  
14  
12  
12  
10  
10  
8
14  
12  
12  
10  
10  
8
14  
12  
10  
10  
8
12  
10  
10  
8
12  
10  
8
3-4  
4-5  
8
5-6  
8
6
6-8  
6
6
6
8-10  
10-12  
12-14  
14-16  
16-18  
18-20  
8
6
6
4
8
6
6
4
4
8
6
6
6
4
2
8
6
6
4
4
2
8
6
4
4
2
2
8
6
6
4
4
2
2
FUNCTIONAL DESCRIPTION  
FOREWORD  
The Porter-Cable Variable Speed Belt Sander (Model 352VS) is designed for  
removing old paint and varnish, smoothing rough boards, and fine-surfacing  
wood, metal, plastics, and other materials.  
OPERATION  
INSTALLING AND REMOVING THE ABRASIVE BELT  
DISCONNECT TOOL FROM POWER SOURCE.  
1. Place the sander on its left  
side.  
2. Pull the lever (A) Fig. 1 out  
toward the front of the machine  
to retract the idler pulley (B) and  
B
release the tension on the  
abrasive belt.  
3. Remove the old belt.  
4. Install the new belt with the  
A
arrow (printed on the inside of  
the belt) on the top and pointing  
TOWARD the idler pulley.  
Fig. 1  
7
 
NOTE: Some sanding belts are bi-directional. These belts will not have  
arrows printed on them. They can be installed to run in either direction.  
5. Engage the front pulley by pushing the lever (A) Fig. 1 back to its original  
position.  
TO START AND STOP THE BELT SANDER  
1. Be certain that the the switch is  
off and the power circuit voltage  
is the same as the voltage shown  
on the specification plate.  
Connect the machine to a power  
circuit.  
2. Squeeze the trigger (A) Fig. 2 to  
start the motor. Release the  
trigger to stop the motor.  
B
A
C
3. To allow the motor to run without  
constantly holding the trigger,  
press the trigger switch (A), push  
the lock button (B) Fig. 2, and  
release the trigger switch.  
Fig. 2  
4. To release the lock button, squeeze the trigger and release.  
VARIABLE SPEED  
Model 352VS has a Variable Speed Control. The operating speed is adjustable  
between 850 SFM (surface feet per minute) and 1300 SFM.  
The speed is adjusted by turning the thumbwheel, (C) Fig. 2. The first position  
provides the slowest operating speed (850 SFM) while position 6 is the fastest  
(1300 SFM). The speed can be changed either when the motor is running or is  
stopped.  
TRACKING THE ABRASIVE BELT  
To prevent excessive wear on both the sander and belt, NEVER allow the  
abrasive belt to rub on the sander frame. To make sure that the belt is tracking  
correctly, do the following:  
Make sure that the trigger switch is “OFF” before con-  
necting the tool to the power source.  
1. Turn the tool over. Hold the rear  
handle with the left hand so that  
A
the ring finger and the little  
finger rest on trigger (Fig. 3).  
2. Squeeze the trigger to start the  
motor.  
3. Turn the belt aligning screw (A)  
in either direction until the edge  
of the belt is even with the outer  
edge of the rear rubber-  
covered pulley. The edge of the  
belt will extend beyond the  
edge of the front pulley.  
Fig. 3  
8
 
4. Release the trigger to stop the motor. Allow the tool to come to a  
COMPLETE STOP before turning it over and putting it down.  
ATTACHING AND CARE OF DUST BAG  
Attach the dust bag to the sander by  
pushing the dust bag tube into the  
sander vacuum housing (Fig. 4).  
For the most efficient operation,  
empty the dust bag when it is  
approximately half full. Pull the dust  
bag straight out of the vacuum  
housing, unzip the rear of the bag,  
and shake out the dust. Every so  
often, turn the bag inside out and  
brush the accumulated dust from  
the inside.  
Fig. 4  
Do not operate the tool without a dust bag or a dust collection  
system.  
SELECTING AN ABRASIVE BELT  
The principle abrasive materials used on belts for machine sanding are aluminum  
oxide and silicon carbide. Aluminum oxide is the softer of the two, but is tougher  
and more suited for woods and soft (non-ferrous) metals. Silicon carbide is  
extremely hard and is best suited for surfacing stone, marble, and glass.  
Abrasives are classed as open-coated (with grits spaced apart), or closed-  
coated (with grits close together). Closed coatings provide hard, fast cutting  
action for hardwoods and dense metals, while open coatings are more suited  
to soft materials and painted surfaces.  
To obtain the best finish, start with a “COARSE” grade of abrasive and change  
to “MEDIUM” and then to“FINE” as work progresses.  
GENERAL SANDING  
SECURE THE WORK and maintain a FIRM GRIP on the  
sander. Friction between the sanding belt and the work will  
tend to move the work backward and the sander forward.  
ALWAYS be sure that the switch is OFF before connecting  
the tool to the power source.  
1. Hold the sander off the work before starting the motor.  
2. Lower the sander to the work, touching the rear part of the belt first. Level  
the machine when moving it forward.  
3. Guide the machine over the work in overlapping strokes. Allow the sander  
to do the work.  
4. Avoid applying excessive pressure. The weight of the machine is usually  
sufficient for a fast smooth finish. A slight increase in pressure may speed  
removal of material, but too much pressure will slow the motor and  
decrease removal.  
9
 
5. Work back and forth over a fairly wide area to obtain an even surface.  
6. Do not let the tool tilt. The edge of the belt can make a deep cuts into the  
surface.  
7. Do not pause in any one spot during the sanding operation. The belt will  
eat into the work and make the surface uneven.  
8. Lift the tool from the work before turning the motor off.  
9. Always be sure that the motor has completely stopped before putting the tool  
down.  
FAST SANDING ON ROUGH WORK  
To smooth a rough surface quickly,  
use a coarse grit abrasive belt. With  
the belt positioned diagonally  
across the grain, move the tool in  
the direction of the grain (Fig. 5).  
Overlap the strokes and cover the  
entire surface, working from both  
sides of the board (angle left and  
then angle right.) Smooth the  
surface by guiding the sander back  
and forth with the grain. Change the  
belt to a medium grit and follow the  
same procedure.  
Fig. 5  
Finish by thoroughly working the grain lengthwise. Change again to a fine grit  
and repeat. Always finish sanding with the grain.  
REMOVING OLD PAINT AND VARNISH  
Read and follow “ADDITIONAL SAFETY RULES FOR  
PAINT REMOVAL” section of this manual.  
The 352VS is an excellent tool for removing old paint and varnish from flat  
surfaces. However, two problems are common: 1) sanding material that loads  
the abrasive and, 2) friction heat caused by working too long in one place. To  
overcome the loading problem, use a coarse grit open coat abrasive belt and a  
single stroke action. Overheating can be avoided by using a fairly quick stroke  
and moving to another area quickly. A piece of felt about 1/4" thick can be  
inserted under the shoe for fast spot sanding and for working on stubborn  
areas of paint and varnish.  
SPECIAL SANDING PROCEDURES  
Generally, the operator should sand with a back and forth motion. Some  
materials and some types of operations, however, require a different  
technique. In rough sanding, use the tool at an angle. In spot sanding, use the  
tool with only the front pulley touching the surface (especially useful in  
smoothing excess glue from wood joints). On metals, slate, marble, or plastic  
materials, sanding can be done in all different directions because of a lack of  
grain.  
9
10  
 
DOORS AND MILL WORK  
When sanding doors, cabinet frames, sash, storm windows and screens, take  
care to avoid working into the cross grain where one member meets another.  
Notice that the right edge of the belt is visible on the sander. Work carefully  
along the edge where the rail meets the stile. If the joint is slightly uneven, use  
a fine abrasive and very light sanding pressure to smooth it before making  
finishing runs.  
For lengthy work on walls or other vertical surfaces, balance the tool with a  
length of sash cord, two small pulleys, a light wood frame, and a weight that is  
the same as, or slightly less than, the weight of the sander. The frame consists  
of two pieces leaning against a wall with a third piece nailed to their top ends.  
The two pulleys are located so that the weight on one end of the cord will be  
out of the way, but will balance the sander fastened to the other end. When  
starting vertical work, angle the sander so you can see that the belt makes  
contact with the material. As the belt touches, level the machine and make the  
stroke away and to the left. This movement will offset the tendency to cut  
heavily into the work at the start of the stroke.  
GOOD SANDING TECHNIQUE  
Getting to know the sander is most important in obtaining smooth results with a  
minimum of labor. Operators will quickly learn how to start a stroke with a  
sweeping motion to produce the best results. Use a long even stroke without  
additional pressure on the tool. Overlap each stroke and vary the length of  
movement so the results will be even. Always lift the tool from the work before  
starting and stopping the motor.  
BE CAREFUL when sanding at the  
end of a board. Keep the tool level  
and flat on the work surface. Don’t  
let the front of the tool drop. (Fig. 6).  
If this happens, it will round the  
edge.  
Fig. 6  
The model 352VS sander works very fast and can do a thorough job in a fraction  
of the time required by hand sanding. Do not rush the job. Give every surface a  
thorough sanding with each grade of abrasive before changing to finer grits.  
Always use the abrasive material and grit size recommended for the particular  
job.  
SANDING METAL  
Use the Belt Sander to obtain a grained satin finish on metal. A special  
graphite pad is available to replace the steel shoe on the bottom of the sander.  
The softness of this pad aids in blending the graining. The pad is the proper  
length for sanders using a 3" x 24" belt. For sanders using shorter belt lengths,  
cut the pad so that it is the same length as the steel shoe. Replace the steel  
shoe with the graphite pad.  
11  
 
MAINTENANCE  
KEEP TOOL CLEAN  
Periodically blow out all air passages with dry compressed air. All plastic parts  
should be cleaned with a soft damp cloth. NEVER use solvents to clean  
plastic parts. They could possibly dissolve or otherwise damage the material.  
Wear safety glasses while using compressed air.  
FAILURE TO START  
Should your tool fail to start, check to make sure the prongs on the cord plug  
are making good contact in the outlet. Also, check for blown fuses or open  
circuit breakers in the line.  
LUBRICATION  
This tool has been lubricated with a sufficient amount of high grade lubricant  
for the life of the unit under normal operating conditions. No further lubrication  
is necessary.  
BRUSH INSPECTION AND LUBRICATION  
For your continued safety and electrical protection, brush inspection and  
replacement on this tool should ONLY be performed by an AUTHORIZED  
PORTER-CABLE SERVICE STATION or a PORTER-CABLE/DELTA  
FACTORY SERVICE CENTER.  
At approximately 100 hours of use, take or send your tool to your nearest  
authorized Porter-Cable Service Station to be thoroughly cleaned and  
inspected. Have worn parts replaced and lubricate with fresh lubricant. Have  
new brushes installed, and test the tool for performance.  
Any loss of power before the above maintenance check may indicate the  
need for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE  
TOOL UNDER THIS CONDITION. If proper operating voltage is present, return  
your tool to the service station for immediate service.  
SERVICE AND REPAIRS  
All quality tools will eventually require servicing or replacement of parts due to  
wear from normal use. These operations, including brush inspection and  
replacement, should ONLY be performed by either an AUTHORIZED  
PORTER-CABLE SERVICE STATION or a PORTER-CABLE/DELTA FACTORY  
SERVICE CENTER. All repairs made by these agencies are fully guaranteed  
against defective material and workmanship. We cannot guarantee repairs  
made or attempted by anyone other than these agencies.  
Should you have any questions about your tool, feel free to write us at any  
time. In any communications, please give all information shown on the  
nameplate of your tool (model number, type, serial number, etc.).  
12  
 
ACCESSORIES  
A complete line of accessories is available from your Porter-Cable ·  
Delta Supplier, Porter-Cable · Delta Factory Service Centers, and  
Porter-Cable Authorized Service Stations. Please visit our Web Site  
www.porter-cable.com for a catalog or for the name of your nearest  
supplier.  
Since accessories other than those offered by Porter-  
Cable· Delta have not been tested with this product,  
use of such accessories could be hazardous. For safest  
operation, only Porter-Cable · Delta recommended  
accessories should be used with this product.  
13  
 
PORTER-CABLE LIMITED  
ONE YEAR WARRANTY  
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original  
purchase. We will repair or replace at our option, any part or parts of the product and accessories  
covered under this warranty which, after examination, proves to be defective in workmanship or  
material during the warranty period. For repair or replacement return the complete tool or accessory,  
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.  
Proof of purchase may be required. This warranty does not apply to repair or replacement required  
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service  
Centers or Authorized Service Stations.  
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE  
OF PURCHASE.  
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,  
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING  
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY  
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL  
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied  
warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above  
limitation or exclusion may not apply to you.  
This warranty gives you specific legal rights and you may also have other legal rights which vary  
from state to state.  
14  
 
PORTER-CABLE • DELTA SERVICE CENTERS  
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)  
(CENTRE DE SERVICE PORTER-CABLE • DELTA)  
Parts and Repair Service for Porter-Cable  
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable  
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)  
Delta Power Tools are Available at These Locations  
Delta)  
Cleveland 44125  
8001 Sweet Valley Drive  
Unit #19  
Phone: (216) 447-9030  
Fax: (216) 447-3097  
ARIZONA  
MINNESOTA  
Minneapolis 55429  
5522 Lakeland Avenue North  
Phone: (763) 561-9080  
Fax: (763) 561-0653  
ILLINOIS  
Tempe 85282 (Phoenix)  
2400 West Southern Avenue  
Suite 105  
Phone: (602) 437-1200  
Fax: (602) 437-2200  
Addison 60101 (Chicago)  
400 South Rohlwing Rd.  
Phone: (630) 424-8805  
Fax: (630) 424-8895  
OREGON  
Portland 97230  
4916 NE 122 nd Ave.  
Phone: (503) 252-0107  
Fax: (503) 252-2123  
MISSOURI  
Woodridge 60517 (Chicago)  
2033 West 75th Street  
Phone: (630) 910-9200  
Fax: (630) 910-0360  
CALIFORNIA  
North Kansas City 64116  
1141 Swift Avenue  
Phone: (816) 221-2070  
Fax: (816) 221-2897  
Ontario 91761 (Los Angeles)  
3949A East Guasti Road  
Phone: (909) 390-5555  
Fax: (909) 390-5554  
San Leandro 94577 (Oakland)  
3039 Teagarden Street  
Phone: (510) 357-9762  
Fax: (510) 357-7939  
MARYLAND  
St. Louis 63119  
Elkridge 21075 (Baltimore)  
7397-102 Washington Blvd.  
Phone: (410) 799-9394  
Fax: (410) 799-9398  
7574 Watson Road  
Phone: (314) 968-8950  
Fax: (314) 968-2790  
PENNSYLVANIA  
Willow Grove 19090  
520 North York Road  
Phone: (215) 658-1430  
Fax: (215) 658-1433  
NEW YORK  
MASSACHUSETTS  
Braintree 02185 (Boston)  
719 Granite Street  
Phone: (781) 848-9810  
Fax: (781) 848-6759  
COLORADO  
Flushing 11365-1595 (N.Y.C.)  
175-25 Horace Harding Expwy.  
Phone: (718) 225-2040  
Fax: (718) 423-9619  
Arvada 80003 (Denver)  
8175 Sheridan Blvd., Unit S  
Phone: (303) 487-1809  
Fax: (303) 487-1868  
TEXAS  
Carrollton 75006 (Dallas)  
1300 Interstate 35 N, Suite 112  
Phone: (972) 446-2996  
Fax: (972) 446-8157  
NORTH CAROLINA  
Charlotte 28270  
9129 Monroe Road, Suite 115  
Phone: (704) 841-1176  
Fax: (704) 708-4625  
Franklin 02038 (Boston)  
Franklin Industrial Park  
101E Constitution Blvd.  
Phone: (508) 520-8802  
Fax: (508) 528-8089  
FLORIDA  
Davie 33314 (Miami)  
4343 South State Rd. 7 (441)  
Unit #107  
Phone: (954) 321-6635  
Fax: (954) 321-6638  
Tampa 33609  
4538 W. Kennedy Boulevard  
Phone: (813) 877-9585  
Fax: (813) 289-7948  
Houston 77055  
West 10 Business Center  
1008 Wirt Road, Suite 120  
Phone: (713) 682-0334  
Fax: (713) 682-4867  
OHIO  
MICHIGAN  
Columbus 43214  
4560 Indianola Avenue  
Phone: (614) 263-0929  
Fax: (614) 263-1238  
Madison Heights 48071 (Detroit)  
30475 Stephenson Highway  
Phone: (248) 597-5000  
Fax: (248) 597-5004  
WASHINGTON  
Auburn 98001(Seattle)  
3320 West Valley HWY, North  
Building D, Suite 111  
Phone: (253) 333-8353  
Fax: (253) 333-9613  
GEORGIA  
Forest Park 30297 (Atlanta)  
5442 Frontage Road,  
Suite 112  
Phone: (404) 608-0006  
Fax: (404) 608-1123  
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts and  
accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized Service  
Center, or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to  
the nearest Porter-Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades.  
Llame al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter-  
Cable Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable Delta, Centro de Servicio Autorizado o Centro  
de Servicio de Fábrica Porter-Cable Delta. Si no tiene acceso a ninguna de estas opciones, llame al 888-848-5175 y le dirigirán al Centro de  
Servicio de Fábrica Porter-Cable Delta más cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au  
800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-  
Cable  
Delta, s’adresser à tout distributeur Porter-Cable  
Delta, centre de service agréé ou centre de service d’usine Porter-Cable  
Delta. Si  
Delta le  
vous n’avez accès à aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable  
plus proche.  
QUÉBEC  
ALBERTA  
MANITOBA  
1515 Ave.  
Bay 6, 2520-23rd St. N.E.  
Calgary, Alberta  
T2E 8L2  
1699 Dublin Avenue  
Winnipeg, Manitoba  
R3H 0H2  
St-Jean Baptiste,  
Québec, Québec  
G2E 5E2  
Phone: (418) 877-7112  
Fax: (418) 877-7123  
Phone: (403) 735-6166  
Fax: (403) 735-6144  
Phone: (204) 633-9259  
Fax: (204) 632-1976  
BRITISH COLUMBIA  
8520 Baxter Place  
Burnaby, B.C.  
V5A 4T8  
Phone: (604) 420-0102  
Fax: (604) 420-3522  
ONTARIO  
1447, Begin  
St-Laurent, (Montréal), Québec  
H4R 1V8  
Phone: (514) 336-8772  
Fax: (514) 336-3505  
505 Southgate Drive  
Guelph, Ontario  
N1H 6M7  
Phone: (519) 836-2840  
Fax: (519) 767-4131  
The following are trademarks of PORTER-CABLE  
DELTA (Las siguientes son marcas registradas de PORTER-CABLE  
DELTA S.A.) (Les  
marques suivantes sont des marques de fabriquant de la PORTER-CABLE  
DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®,  
Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®,  
Flying Chips™, FRAME SAW®, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®,  
Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-  
CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, Posi-Matic®, Q-3®&(design), QUICKSAND®&(design), QUICKSET™,  
QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®, Sanding Center®, SANDTRAP®&(design), SAW BOSS®,  
Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®, The American Woodshop®&(design), The Lumber  
Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®,  
TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®,  
Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®, WOODWORKER’S CHOICE™.  
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other  
countries. Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y  
también pueden estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets  
d’invention et marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.  
Printed in U.S.A. PC-0403-150  
 

Philips Cassette Player AQ4010 05 User Manual
Philips Hair Clippers QC5115 User Manual
Philips Laptop Docking Station DS6100 User Manual
Philips Portable DVD Player PET702 75 User Manual
Philips Projection Television 54XP43C 37 User Manual
Philips Telephone CORD282 User Manual
Planar Computer Monitor PQ1910M User Manual
Plustek Scanner SmartOffice User Manual
Premier Mounts Indoor Furnishings PP TL User Manual
PYLE Audio Musical Instrument PYD 1002 User Manual